Radiolink R4FG, 2.4GHz 4 channels receiver, TI CC2500 communication chip, gyro integrated and
HV servo supported. Compatible with Radiolink 4 channels radio RC3S, RC4G and 8 channels transmitter T8FB.
How to Match Code With Transmitter :
1. Put the transmitter and the receiver close to each other within 50 centimeters.
2. Turn on the transmitter, then power on the R4FG.
3. There is a black button on the R4FG, press the binding button twice in two seconds and release, receiver light start blinking, after about blinking 8 times, match code success then receiver signal LED always on!
Attention: R4FG default have not turn on the gyro function. Make sure the R4FG keep motionless when power on it, because the R4FG will do the self-test.
R4FG with two indicate LED, green LED on indicate normal working mode while both green and red LED on indicate gyro function working mode.
Working Mode
R4FG has two working modes:normal working mode and gyro function working mode.
Normal Working Mode
Green LED, gyro will not working.
Gyro Function Working Mode
Both green and red LED on.
Receiver with gyro integrated to hold the vehicle in a straight line during aggressive acceleration and braking or get bumped around by rough terrain.
Receiver with gyro integrated to keep the uni-direction and anti-slip.
How to Turn On Gyro Function
Quick press the ID SET switch two times within 1 second, the LED change from green to red means gyro function has turn on.
Gyro Function Setup
Resume
Integrated Gyro, is used to assure the stability of cars on turning status; and keep on straight running even the cars get some mechanical phantom. Gyro function can be enabled or disabled.
PARAMETER INSTRUCTION
A. Gyro enabled
Gyro preset disabled, and it enters post indication status. There are two indicators on the receiver. The green one shows the receiver status and the red one is for gyro. When the led turns on, the gyro is enabled , and the led turns off, gyro disabled.
B. Gyro enabled forward
Cars can be drove forward and backward, gyro is enabled forward or backward correspondingly. Like the EP cars, different connection will make different direction, the gyro is ensured to be enable forward.
C. Gyro reverse
Same like a plane has reverse, car kit gyro has reverse as well. Only right set reverse gyro can act to correct.
Set
1. Enable gyro
Press binding key three time (interval less than 1 second), the red LED will flash three time, indicating whether gyro is enabled.
2. Gyro sensitivity
Gyro sensitivity is predefined to adjust by channel three (factory set VR function), turning the VR switch clockwise to raise sensitivity and anti-clockwise to decrease.
3. Gyro forward
When the gyro is enabled, pull the throttle trigger and then release (make sure the car stops running), turn the car right or left without changing steering wheel, if the servo will not follow with, it shows gyro is set backward. Press the binding switch one time less than 1 second, the LED flashes red once, gyro is changed to act forward.
4. Gyro reverse
Set the gyro forward, turn the car right or left to see whether gyro functions. The wheel will turn left when the car is turned right and the wheel turns right when the car is turned left. If the gyro acts counter, press the binding switch two time, the LED flashes two time red, the gyro reverse is corrected.
Specification
1) Size: 35*20*13mm
2) Channel: 4
3) Model: cars, boats
4) Modulation mode: GFSK
5) Spread spectrum: FHSS
6) 10 modes memory storage
7) Antenna length: 106mm
8) Control distance: more than 400 meters
9) LCD screen: 128*64 resolution, LCD back light
10) Power supply: 4.8~15.0V DC, 4*1.5AA or 2S-4S Lithium battery
11) RF power: <10dbm
12) Low voltage alert: Yes (lower than 4.6V), can be set when using 2S-4S Li-Po battery
13) Frequency: 2.4GHz ISM band(2400MHz~2483.5MHz)
14) Channel resolution: 4096
15) Work current: 80~120mA
16) Compatible with transmitters: RC4GS, RC3S, RC4G, T8FB
1.R4FG User Manual load check Here
